[Feb-2026] Dumps Practice Exam Questions Study Guide for the NS0-014 Exam

NS0-014 Dumps with Practice Exam Questions Answers

NEW QUESTION # 13
Which technology allows MetroCluster to provide zero data loss failover?

• A. SyncMirror
• B. Snapshot
• C. SnapVault
• D. ONTAP Mediator

Answer: A

NEW QUESTION # 14
Which two network configurations are supported by MetroCluster? (Select two)

• A. MPLS MetroCluster
• B. IP MetroCluster
• C. VPN MetroCluster
• D. FC MetroCluster

Answer: B,D

NEW QUESTION # 15
Which two components must be validated to ensure the proper functioning of a Fibre Channel MetroCluster configuration? (Choose two)

• A. Fibre Channel zoning
• B. Mediator configuration
• C. ATTO Bridge health
• D. SnapMirror configuration

Answer: A,C

NEW QUESTION # 16
A customer has a MetroCluster in which one site had suffered a power outage. The MetroCluster performed a switchover to the secondary site. The storage administrator is now preparing to run a DR switchback, to restore normal operations across the two sites for the MetroCluster.
Which two commands does the administrator have to run before the switchback? (Choose two).

• A. metrocluster heal root-aggregates
• B. metrocluster heal aggregates
• C. snapmirror resync
• D. storage aggregate mirror

Answer: A,B

NEW QUESTION # 17
In the event of a MetroCluster replication failure, which two steps should be taken to troubleshoot? (Choose two)

• A. Validate RDB consistency
• B. Check SnapMirror schedules
• C. Disable the FC switches
• D. Check the cluster interconnect status

Answer: A,D

NEW QUESTION # 18
What are two key indicators of a successful switchover test in a MetroCluster environment?
(Select two)

• A. Replication traffic switches to the secondary site
• B. All data services remain available during the test
• C. The secondary site remains in read-only mode
• D. Replication traffic switches to the secondary site

Answer: B,D

NEW QUESTION # 19
What is the primary purpose of the MetroCluster Tiebreaker in disaster recovery testing?

• A. To verify that storage shelves are properly synchronized
• B. To perform data deduplication
• C. To manage automatic failover between sites
• D. To automatically upgrade ONTAP

Answer: C

NEW QUESTION # 20
What are two requirements when transitioning from FC MetroCluster to IP MetroCluster? (Select two)

• A. Maintain existing FC paths
• B. Replace FC switches with IP switches
• C. Remove ATTO FibreBridges
• D. Upgrade to a compatible ONTAP version

Answer: B,D

NEW QUESTION # 21
Which switch configuration is necessary for the communication between MetroCluster nodes?

• A. Ethernet switches in loop mode
• B. Fibre Channel over Ethernet (FCoE) switches
• C. FC switches with ISL links
• D. IP-based switches with cross-links

Answer: C

NEW QUESTION # 22
Which tool is used to verify a customer environment's compatibility with MetroCluster before deployment?

• A. OnCommand Workflow Automation
• B. SnapCenter
• C. System Manager
• D. Config Advisor

Answer: D

NEW QUESTION # 23
When implementing a MetroCluster solution, which two configurations are required to ensure data redundancy across sites? (Select two)

• A. Use of Snapshot copies
• B. Single path network configuration
• C. SyncMirror enabled for all volumes
• D. Use of Snapshot copies

Answer: C,D

NEW QUESTION # 24
What is the main function of the metrocluster check command in ONTAP?

• A. To perform a complete configuration backup
• B. To initiate a storage failover
• C. To verify that MetroCluster components are functioning properly
• D. To force a site switchover

Answer: C

NEW QUESTION # 25
When planning MetroCluster, what is the recommended minimum WAN bandwidth for IP communication between two sites?

• A. 10 Gbps
• B. 100 Mbps
• C. 10 Mbps
• D. 1 Gbps

Answer: D

NEW QUESTION # 26
Which MetroCluster component requires reconfiguration when upgrading from a 2-node to a 4- node configuration?

• A. SyncMirror
• B. ATTO FibreBridge
• C. Mediator
• D. FC switches

Answer: D

NEW QUESTION # 27
Which of the following are critical factors in planning a MetroCluster deployment? (Select two)

• A. WAN bandwidth
• B. Office furniture layout
• C. Network latency between sites
• D. Rack size

Answer: A,C

NEW QUESTION # 28
What is the minimum number of required data centers for a NetApp MetroCluster installation?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: D

NEW QUESTION # 29
What is the recommended maximum latency for the round-trip between two MetroCluster sites?

• A. 5 ms
• B. 10 ms
• C. 1 ms
• D. 15 ms

Answer: B

NEW QUESTION # 30
When the administrator of a MetroCluster configuration creates a mirrored aggregate on the local cluster, which action automatically occurs on both clusters?

• A. A failover group is created.
• B. An SVM DR is created.
• C. A plex is created.
• D. A DR group is created.

Answer: C

NEW QUESTION # 31
When transitioning from FC to IP MetroCluster, which two components must be replaced? (Select two)

• A. ATTO FibreBridges
• B. Mediator software
• C. Ethernet switches
• D. Fibre Channel switches

Answer: A,D

NEW QUESTION # 32
......

Free NetApp Implementation Engineer NS0-014 Exam Question: https://testking.braindumpsit.com/NS0-014-latest-dumps.html