New HPE6-A80 Test Materials & Valid HPE6-A80 Test Engine

HPE6-A80 Updated Exam Dumps [2022] Practice Valid Exam Dumps Question

NEW QUESTION 33
Refer to the exhibit.

The exhibit shows the current AP deployment in a school. This customer indicates that the current wireless performance is inadequate and w B02.11ax.
For the new' solution, what should the network architect recommend?

• A. APs deployed in rooms with a density-based design
• B. APs deployed in hallways with about twice the density
• C. APS deployed in similar locations, but with higher gain antennas
• D. APs deployed in similar locations, but with dual 5 GHz radios

Answer: B

 

NEW QUESTION 34
An indoor sports stadium has 5.000 seats in two rings:
* The stadium has a ceiling height of 72 feet (22 m).
* There is a catwalk around the perimeter of me stadium that is 54 feet (13 m) from me floor.
* There are two scoreboards at either end of the stadium
* The construction of the stadium is concrete and steel.
The customer has indicated a preference for overhead coverage, and the wireless network should support 3500 concurrent clients. The architect plans to install the APs on the catwalk to service sections of the floor below Which type or antennas are recommended for the APS that provide the overhead coverage?

• A. downtilt
• B. high gain directional
• C. vagi
• D. high gain omnidirectional

Answer: B

 

NEW QUESTION 35
Refer to the exhibit.


A customer needs a new branch office solution that:
provides 802.11ac wireless access to local resources and the local Internet connection connects wired and wireless users to resources at the main office in a secure manner The office has 200 users, who will the up to two wireless devices at the same time. The architect has determined that the office requires 10-13 AP-
515s. The customer wants to support a total bandwidth from an or me APS or about 2 cops.
The entire site is currently wired for CAT5e from a single wiring closet, which contains two access switches, a core switch, and the Internet cable modem, which has 10/10O/1OQO Mbps BASE-T ports. The wired networK will handle abouti Gbps of traffic. The switches do not support P0E/P0E+.
About 75 percent of all traffic is destined to the main office
The architect has looked up these specs for 7000 series controllers.
Which MC will meet the needs in the most cost-effective manner?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: C

 

NEW QUESTION 36
A mall requires a wireless network upgrade to 802 -Max The company that owns the mall wants to provide the APs for the entire mall. However, several of the larger national chain retailers with spaces in the mall want to offer wireless services with their own SSIDs.
These individual retailers also have their own wireless guest services and wireless client devices They have their own corporate infrastructure and want to handle all of this wireless traffic on their own, including terminating the traffic on their own controllers. The mall requires redundancy for its services, out the retailers do not.
Which plan for mobility controllers (MCs) and mobility master (MW) meets the needs of this scenario?

• A. two MCs for the mall company and one MC for each retailer with its own SSIDs, all controlled by the same pair of MMs
• B. a pair of MMs for the mall company, but not MCs: MMs control one MC for each retailer with its own SSIDs
• C. two MCs for the mail company controlled by a pair of MMS; one standalone MC for each retailer with its own SSIDS
• D. two MCs for the mall company and for all of the retailers, both controlled by the same pair of MMs

Answer: B

 

NEW QUESTION 37
Refer to the exhibit.

A customer has these availability requirements;
* loss of one controller with stateful failover and without impact on wireless client connectivity
* loss of one core switch without loss of connectivity for any endpoints or APs in the building
* loss of any one switch-lo-switch or MC-to-switch link without loss of connectivity for any endpoints or APS in the building and with minimal impact on infrastructure functionality
* loss of any one access switch with minimal impact to wireless client connectivity The exhibit shows the current plan for the topology.
Which change should the architect make to the plan to provide better support for the customers availability requirements?

• A. Change the 40GbE DAC on the 8400 switch to a stacking cable with stacking module.
• B. Add VLANs 11 and 15 to the MC connections to ensure both MCS can manage any of the APS.
• C. Use two 40GBE DACs between the core V3X switches for their switch links.
• D. Add 120 additional AP licenses, so that each MC can support ail the APs, even if the other MC fails.

Answer: D

 

NEW QUESTION 38
Refer to the exhibit.

The exhibit shows the design for an existing network. The customer intends to replace the current Core switches with two Aruba 8400 switches.
What are two points that the architect should ensure that the customer understands? (Select two.)

• A. The 8400 switches run different software than the 5400R switches.
• B. The 8400 switches have a smaller ARP table than the 540OR switches.
• C. The 8400 switches are fixed port switches.
• D. The 8400 switches do not support VSF.
• E. The 8400 switches cannot be monitored by AirWave.

Answer: A,B

 

NEW QUESTION 39
For which scenario do Aruba CX 6300M Series switches meet the needs for an upgrade of the wired access layer while the Aruba CX 630QF Series switches do not?

• A. The customer wants to utilize the Aruba AP-515 support for 002 3bz connectivity.
• B. The Aruba CX 630DM support up to 75W PoE+ per port
• C. The customer wants to utilize LACP on AP515 in VSF switch configuration.
• D. The Aruba CX6300M supports 10GBase-T connectivity with AP-515.

Answer: B

 

NEW QUESTION 40
An archinect needs lo plan a Mobility Master (MM) solution for a customer Requirements include:
* redundancy for the MM
* redundancy for the MCS (seamless failover if up to one fails)
The wireless network consists of
* total APs - 300
* total wireless devices = 20,000
* total MCs = 10
The customer wants the most cost-effective plan that meets me requirements.
Which plan for MMs should the architect select?

• A. 1 MM-HW-5K and 1 MM-VA-1K
• B. 1 MM-HW-5K and 1 MM-HW-1K
• C. 2 MM-HW-1QK
• D. 2 MM-HW-5K

Answer: C

 

NEW QUESTION 41
An indoor basKetbaiI stadium has 5.000 seats in two rings:
* The stadium has a ceiling height of GO feet (18 m).
* There is a catwalk around the perimeter of the basketball court, between the court and the seating areas.
* This catwalk is 40 feet (12 m) from the floor.
* There are two scoreboards at either end of the stadium.
* The construction of the stadium is concrete and sleet.
The customer does not want an under-seat, picoceli deployment.
Which AP model is appropriate to provide coverage in the main stadium bawl?

• A. AP-555
• B. AP-575
• C. AP-577
• D. AP-505

Answer: C

 

NEW QUESTION 42
A hospital wireless network must support many different types of users and devices, including:
* Visitors who access the Internet
* Admin staff, who run applications such as scheduling
* Medical staff, who look up patient info on their tablets
* Patient monitoring devices, which must not lose any traffic
* Communicator badges, which support real-time voice to allow nurses and doctors to communicate The hospital needs to ensure that the most vital and time-sensitive traffic is prioritized and that visitors do not interfere with hospital applications. The MC should mark traffic that passes through it for an appropriate priority.
Which plan meets the needs? (The plans describe firewall roles and rules but do not need to use correct syntax. Note that security roles are also not included.)

• A. Patient monitoring = Highest. Medical staff = Highest. communicators = High. Admin staff = High. Visitors = Normal.
• B. Communicator = Highest. Patient monitoring = Highest. Medical staff = High. Admin staff = Normal: Visitors = Low.
• C. Medical staff = Highest. Patient monitoring = Highest. Admin staff - High. Communicator = Normal. Visitors = Low.
• D. Medical staff = Highest. Communicator = High. Patient monitoring = High. Admin = High. Visitors = Normal

Answer: C

 

NEW QUESTION 43
Refer to the exhibit.

A customer needs a wired upgrade for a building on its main campus. The exhibit shows the switches that the architect has selected for each closet and me existing cabling. The customer is not open to changing the cabling.
The customer requires link redundancy for the uplinks from each closet and for the links from the building to the core. In non link failure situations, the uplinks from each closet must support at least 20Gbps, and the building as a whole must have at least 20 Gbps to the core in non link failure situations Which two options Tor connecting the closets to the network core are valid? (select two.)

• A. Connect me Floor 2 switch stack to Floor 1 with two fiber connections, DO me same for Floor 3. connect the Floor 1 switch stack to the network cone with two fiber connections.
• B. Combine the nine switches on all three floors into a single switch slack with stacking cables in a ring topology.
  Connect two Floor f members to the network core with one fiber connection each
• C. Add two aggregation switches in the Floor 1closet. Connect the switch stack for each closet to the aggregation switches on two fiber links each and the aggregation switches to the core on two fiber links.
• D. Connect the switch stack on each floor directly to the network cone on two "fiber connections per floor. Achieve this by patching the inter-floor fiber through to the inter-building fiber.
• E. Combine the nine switches on the three floors into a single switch stack with the MM QM3 fiber cables in a ring topology. Connect two Floor 1 members to the network core with one fiber connection each.

Answer: C,D

 

NEW QUESTION 44
Refer to the exhibit.
A customer has an existing network with ArubaOS switches, Aruba 7205 controller, and 802.11ac APs. The customer needs a wired upgrade for their campus network and wireless upgrade with 802,11ax APs and would like to get all the functions of AP.
The customer has one building with 3 floors with the following wired devices,
* 200 VOIP phones
* 8 printers
* security cameras
The architect plans to propose 75 AP-535s.
The security cameras are a high definition pan-tilt-zoom with heaters for harsh environments that require more than 45 W to function, Which exhibit shows an access switch mat meets the customer needs?
A)

B)

C)

D)

• A. Option A
• B. Option D
• C. Option C
• D. Option B

Answer: B

 

NEW QUESTION 45
Refer to the exhibit.

The exhibit shows the topology for a new Aruba solution. The MCs are in a ctuster and support all of the wireless traffic in the network The core switches route all traffic and support all VLANS. The access fayer switches do NOT use tunneiednode. or dynamic segmentation.
The customer has indicated that it has these VLANS for user devices.
* VLAN 11 for Floori employee wired devices
* VLAN 12 for Floor 2 employee wired devices
* VLAN 13 tor Floor 3 employee wired devices
* VLAN 14 for Floor 4 employee wired devices
* VLAN 15 for Floor 5 employee wired devices
* VLAN 101 for all employee wireless devices
* VLAN 102 for all guest wireless devices
In which locations should the architect plan the VLANs?

• A. VLANS 11-15 on the access layer switches on the corresponding floor; VLANS 101 and 102 on both MCS.
• B. VLANs 11-15 on one MC. VLANs 101 and 102 on the other MC. (Other VLANs will be used on the access layer switches.)
• C. VLANs 11-15 on the access layer switches on the corresponding floor; VLAN 101 on one MC and VLAN 102 on me other MC
• D. VLANs 11-15. 101. and 102 on both MCs. (Other VLANs will be used on the access layer switches.)

Answer: C

 

NEW QUESTION 46
A customer has an Aruba solution with APs, MCs, and an MM The customer also uses AirWave and ClearPass. The customer wants to add Aruba CX Switches, which use per-user tunneled node, to the solution.
How should the Aruba CX Switches integrate with the existing solution in order to determine when to tunnel device traffic to MCs?

• A. They should be directed to MCs by a DHCP or DNS server.
• B. They should be manually added as MDs in MM.
• C. They should be managed by AirWave with SNMPv3.
• D. They should implement authentication to ClearPass.

Answer: A

 

NEW QUESTION 47
Which scenario Indicates the need for a wireless mesh?

• A. A company needs to provide seamless roaming and wireless access between two buildings. The buildings are about 60 feet (18 m) apart.
• B. A nsstorical building has some wired areas and a few areas with no wired or wireless connectivity, walls and ceilings have asbestos. The company needs wireless access across the site.
• C. A company has a small branch office with just one RAP. The company has noticed that performance is poor in some areas of the network and wants to add another AP.
• D. A hospital needs to provide high availability for wireless services in certain areas which support very critical wireless medical devices. Devices must always be in range of at least two APs.

Answer: A

 

NEW QUESTION 48
Refer to the exhibit.

A customer has the wined infrastructure shown in the exhibit. The customer is in the process of expanding their wireless services They will now add a new wireless solution, with mobility controllers (MCs) connected as shown. The new wireless solution will support a total of 450 APs and about 26,000 wireless devices. It must provide seamless roaming across the entire campus.
After the new deployment, both wired and wireless devices experience IP connectivity issues.
Which change to the existing infrastructure should the architect recommend to support all of the customer requirements?

• A. The wired VLANS should be combined into a single VLAN and n6 subnet
• B. The core and aggregation switches should disable Virtual Switching Framework (VSF).
• C. The core switches should be replaced with switches that have larger ARP tables.
• D. The MCs should be moved to the aggregation layer, and more MCs added

Answer: B

 

NEW QUESTION 49
A company already has an Aruba wireless network The network currently consists of:
* oneMM-HW-1k
* two 7210 MCs in the network core
* two 721GMCsintheDMZ
* 200 AP-515S in Building 1 and Building 5
100 AP-515S each In Building 2r Building 3, and Building 4
The customer now wants to assess if it needs local Mobility controllers (MC) for any buildings:
- Building 1 is the main office building for the campus. It supports the highest number of APs. It connects to the network core without an aggregation layer.
* Building 2 is further away from the Building i. and no roaming is provided between it and the other buildings its access layer connects to the network cone with a pair of Aruba CX 6300M aggregation switches.
* Building 3 is further away from the other buildings, it connects to the network core without an aggregation layer.
The Guest SSID traffic should be tunnelled to the DMZ controllers
' Building 4 has its own local datacenter and Internet connection. The company would like it to be able to operate completely autonomously if its aggregation layer loses connectivity with the core.
* Building 5 is further away from the other buildings, it connects to the network core without an aggregation layer.
This building has been assigned to a partner that would like to manage a dedicated SS1D using the shared AP infrastructure.
In which two buildings should the network architect plan local mobility controllers (MCs)? (Select two)

• A. Building 4
• B. Building 2
• C. Building 5
• D. Building 3
• E. Building 1

Answer: D,E

 

NEW QUESTION 50
A customer has an existing; Aruba wireless solution to provide wireless access for employees. The solution Includes Aps, mobility controllers (MCs) at the network core, and a Mobility Master (MM} A customer would like to set up a separatelymanaged guest network and have the traffic go directly to the DMZ.
What should the architect suggest as the simplest solution that meets the requirements?

• A. Have a dedicated mobility controller in the DMZ managed by the same MM
• B. Add APs in a dedicated AP group to support only the guest network SSID.
• C. Double the number of APs and controllers.
• D. Use MulitZone, and put a mobility controller in Itie DMZ.

Answer: D

 

NEW QUESTION 51
A customer has an Aruba wireless netwofK with:
* Two 7205 Mobility Controllers (MCs) in a cluster - Each MC must be able to support the complete network in the case of an MC failure
* 250 APs. which support a total of 7.500 devices
* A virtual CxQCQ ClearPass appliance with 1QK Access licenses
* An MM-HW-1K appliance
The customer is interested in an upgrade to Aruba CX Switches, primarily to benefit from the per-user tunneled node feature. The customer requires support for 2500 ports, and 95 percent of wined endpoints will use tunneled node.
Which change to the existing solution should the architect explain?

• A. The Mobility Master will need more MM licenses to support the wired endpoints that use tunneled node.
• B. A new controller will be required to support sufficient clients, including the wired ones.
• C. The clustering feature will need to be disabled on the controllers, so that they can support tunneled node.
• D. A separate ClearPass virtual appliance will be required to integrate with the AQS-Switches

Answer: C

 

NEW QUESTION 52
Refer to the exhibit.

A stadium wants to deploy location-based services, including blue-dot wayfinding over a 200.000 square root (isr580 sq. m) are a. The custom past particular areas. The customer has selected a 1 year subscription.
The exhibit shows the BOM that the architect created in iris.
Which correction should the architect make?

• A. Change the campaign subscription to a Maps subscription.
• B. Add two Maps subscriptions.
• C. Remove one Blue Dot Nav subscription.
• D. Add another campaign subscription.

Answer: A

 

NEW QUESTION 53
A customer has multiple, very small branch sites that require just one or two APs each. The office has a local Internet connection, but all of the traffic is destined To the corporate data center, which has an Aruba wireless solution.
Which branch office solution best meets the customer needs?

• A. RAPs and no branch office controllers
• B. RAPs and 7005 branch office controllers with an. SD-WAN license
• C. CAPS and 7005 branch office controllers
• D. IAPs and 7005 branch office controllers with an 3D-WAN license

Answer: C

 

NEW QUESTION 54
Refer to the exhibit.

A customer needs a wireless network upgrade and has these requirements.
- Support any applications used on a wired connection
- Support up to 2500 wireless clients
- Support seamless roaming from floor to floor and building to building
- Continue to function seamlessly if one controller fails
The architect has designed the logical infrastructure for the network as shown in the exhibit Which change should the architect make to belter meet customer requirements and besl practices?

• A. Combine me /25 subnets for wireless and wired users into a /16 subnet.
• B. Place each controller in a different VLAN and subnet.
• C. Combine the /25 subnets for wireless users into a /20 subnet
• D. Install additional Mobility Controller.

Answer: D

 

NEW QUESTION 55
A network architect needs to plan quality of service (QoS) for a hospital network.
Which of these applications should receive the highest priority?

• A. cloud-based scheduling software
• B. streaming IPTV in lobbies
• C. MRI image transfer
• D. wireless voice communicator devices

Answer: A

 

NEW QUESTION 56
A hospital needs a Getter way to track its inventory Including wireless medical devices that are moved around the site a lot.
Which solution meets these needs?

• A. Aruba beacons and Meridian
• B. Aruba asset tags and beacons
• C. Aruba beacons. APs. and AirWave
• D. Aruba asset tags, APs; and Meridian

Answer: A

 

NEW QUESTION 57
......

HPE6-A80 Sample with Accurate & Updated Questions: https://testking.braindumpsit.com/HPE6-A80-latest-dumps.html